Visit www.usefulequations.com to purchase book and HP 35s pre-programmed calculator package. The equations in this book are relevant to the following subjects: Geotechnical -Moisture content, dry density, void ratio, degree of saturation, relative density of soil, borrow soil, flow net, laboratory permeability tests, and effective stress -Shear strength and angle of internal friction for triaxial test -Net and ultimate bearing capacities of square, continuous, and circular footings with or without water table -Active, passive, and at-rest lateral forces per unit length of wall with surcharge load and water table, and lateral force per unit length of wall for sloping backfill and vertical wall -Gross and net bearing capacity of mat foundation in saturated clay, and depth of fully compensated mat foundation -Factor of safety against overturning and sliding of retaining walls, maximum stress at the toe, and minimum stress at the heel -Settlement of normally consolidated clay with up to 4 layers of soil given surcharge load, settlement at the center and corner of mat foundation, time rate of settlement, slope stability in saturated clay, and cyclic stress ratio -2-strut braced cut for sand, soft to medium clay, and stiff clay -Skin friction resistance, end-bearing and allowable capacities of single pile in sand or clay Water Resources and Environmental -Pitot tube, venturi meter, and orifice -Reynolds number, friction factor, head loss using Darcy-Weisbach equation or Hazen-Williams equation, Bernoulli equation with 2 different pipe sizes, pump head, and head loss due to fittings -Open channels using Manning equation for circular, rectangular, and trapezoidal channels -Flow rate and velocity of flow for circular channel when flowing full or partially full just by entering diameter of pipe, depth of water, Manning's n, constant, and slope of energy line (no need to look up tables!!!) -Flow rate and velocity of flow for trapezoidal channel just by entering depth of water, base width of channel, side slope horizontal, Manning's n, constant, and slope of energy line -Chemical feed rate -Rapid mixing -Overflow rate -Detention time -Weir loading rate Transportation -Sight distance and stopping sight distance -Radius of curve, tangent of curve, length of curve, middle ordinate, and external distance of horizontal curve -Stopping sight distance, passing sight distance, curve elevation, stationing of highest or lowest point of curve, and vertical clearance -Flexible and rigid pavement design Structural -Maximum moment of simply supported and cantilever beams, moment of inertia for I-beam, T-beam, and inverted T-beam using parallel axis theorem, maximum bending stresses, and deflection of beam This book contains 200 equations with keystrokes included for HP 35s and HP 33s calculators plus 96 sample problems with step-by-step solutions.

Easily store equations for the mechanical PE exam in your HP 33s Store 50 frequently used equations 15 specially-selected practice problems, with step-by-step solutions, show you how to use the equations.

FE Mechanical Practice Problems offers comprehensive practice for the NCEES FE Mechanical exam. This book features over 460 three-minute, multiple-choice, exam-like practice problems to illustrate the type of problems you will encounter during the exam. It also features clear, complete, and easy-to-follow solutions to deepen your understanding of all knowledge areas covered on the exam. Additionally, there are step-by-step calculations using equations and nomenclature from the NCEES FE Reference Handbook to familiarize you with the only reference you will have on exam day. For best results, purchase this book along with the FE Mechanical Review. Mechanical Engineering Exam Topics Covered Computational Tools Dynamics, Kinematics, and Vibrations Electricity and Magnetism Engineering Economics Ethics and Professional Practice Fluid Mechanics Heat Transfer Material Properties and Processing Mathematics Materials Measurement, Instrumentation, and Controls Mechanical Design and Analysis Mechanics of Materials Probability and Statistics Statics Thermodynamics Key Features: Over 460 three-minute, multiple-choice, exam-like practice problems Clear, complete, and easy-to-follow solutions Step-by-step calculations using equations and nomenclature from the NCEES FE Reference Handbook Binding: Paperback About the Publisher: PPI, A Kaplan Company has been trusted by engineering exam candidates since 1975.

Fitness, Sportsoziologie, Tests.

Fluid properties and hydraulic units - Hydrostatics - Fundamental concepts of fluid flow - Orifices, gates, and tubes - Weirs - Pipes - Steady uniform flow in open channels - Open channels with nonuniform flow - High-velocity transitions - Wave motion and forces - Spatially variable and unsteady flow - Measurement of flowing water - Computational hydraulics - Computer programs in hydraulics.

Accompanying CD-ROM contains ... "Cases in civil engineering economy, second edition, by William R. Peterson and Ted G. Eschenbach. c2009"--CD-ROM label.

The bestselling step-by-step framing guide—updated and expanded to meet 2018 codes and standards Complete Book of Framing, Second Edition—Updated and Expanded is a comprehensive guide to rough carpentry and framing, written by an expert with over forty years of framing experience. This book guides the reader through step-by-step framing instructions for floors, walls, roofs, door and window openings, and stairs. Hundreds of full-color illustrations and photos enable novice and professional framers to understand and master framing techniques. This Updated and Expanded Second Edition includes the framing techniques of the 2018 International Building Code (IBC), International Residential Code (IRC), and updated OSHA rules. It also includes new coverage of today's electric tools, wind and earthquake framing, medical and physiological factors of framing, and a revised safety chapter. Builders will find information on nailing patters, overall layout, engineered wood patterns, and green framing. In addition, the book offers readers tools and techniques for preparing for a job and managing a team. This Second Edition—Updated and Expanded: Includes hundreds of full-color illustrations depicting step-by-step framing techniques Offers guidance on today's electric tools and structural enhancements for natural disasters Features a revised chapter on safety to reflect the medical and physiological factors of framing Meets the framing techniques of the 2018 International Building Code (IBC), International Residential Code (IRC), and Occupational Safety and Health Administration (OSHA) standards Complete Book of Framing: An Illustrated Guide for Residential Construction, Second Edition—Updated and Expanded is an excellent resource for framers, carpenters, and contractors of all experience levels. Framer-friendly tips throughout the book show how to complete framing tasks efficiently and effectively.