Time-interleaved Analog-to-Digital Converters describes the research performed on low-power time-interleaved ADCs. A detailed theoretical analysis is made of the time-interleaved Track & Hold, since it must be capable of handling signals in the GHz range with little distortion, and minimal power consumption. Timing calibration is not attractive, therefore design techniques are presented which do not require timing calibration. The design of power efficient sub-ADCs is addressed with a theoretical analysis of a successive approximation converter and a pipeline converter. It turns out that the first can consume about 10 times less power than the latter, and this conclusion is supported by literature. Time-interleaved Analog-to-Digital Converters describes the design of a high performance time-interleaved ADC, with much attention for practical design aspects, aiming at both industry and research. Measurements show best-inclass performance with a sample-rate of 1.8 GS/s, 7.9 ENOBs and a power efficiency of 1 pJ/conversion-step.

This book describes techniques for time-interleaving a number of analog-to-digital data converters to achieve demanding bandwidth requirements. Readers will benefit from the presentation of a low-power solution that can be used in actual products, while alleviating the time-varying signal artifacts that typically arise when implementing such a system architecture.

Modern complementary metal oxide semiconductor (CMOS) digital-to-analog converters (DACs) are limited in their bandwidth due to technological constraints. These limitations can be overcome by parallel DAC architectures, which are called interleaving concepts. Christian Schmidt analyzes the limitations and the potential of two innovative DAC interleaving concepts to provide the basis for a practical implementation: the analog multiplexing DAC (AMUX-DAC) and the frequency interleaving DAC (FI-DAC). He presents analytical and discrete-time models as a theoretical foundation and develops digital signal processing (DSP) algorithms to compensate the analog impairments. Further, he quantifies the impact of various limiting parameters with numerical simulations and verifies both concepts in laboratory experiments. About the Author: Christian Schmidt works at the Fraunhofer Heinrich-Hertz-Institute, Berlin, Germany, on innovative solutions for broadband signal generation in the field of optical communications. The studies for his dissertation were carried out at the Technische Universität Berlin and at the Fraunhofer Heinrich-Hertz-Institute, both Berlin, Germany.

Time-interleaved Analog-to-Digital Converters describes the research performed on low-power time-interleaved ADCs. A detailed theoretical analysis is made of the time-interleaved Track & Hold, since it must be capable of handling signals in the GHz range with little distortion, and minimal power consumption. Timing calibration is not attractive, therefore design techniques are presented which do not require timing calibration. The design of power efficient sub-ADCs is addressed with a theoretical analysis of a successive approximation converter and a pipeline converter. It turns out that the first can consume about 10 times less power than the latter, and this conclusion is supported by literature. Time-interleaved Analog-to-Digital Converters describes the design of a high performance time-interleaved ADC, with much attention for practical design aspects, aiming at both industry and research. Measurements show best-inclass performance with a sample-rate of 1.8 GS/s, 7.9 ENOBs and a power efficiency of 1 pJ/conversion-step.

Need to get up to speed quickly on the latest advances in high performance data converters? Want help choosing the best architecture for your application? With everything you need to know about the key new converter architectures, this guide is for you. It presents basic principles, circuit and system design techniques and associated trade-offs, doing away with lengthy mathematical proofs and providing intuitive descriptions upfront. Everything from time-to-digital converters to comparator-based/zero-crossing ADCs is covered and each topic is introduced with a short summary of the essential basics. Practical examples describing actual chips, along with extensive comparison between architectural or circuit options, ease architecture selection and help you cut design time and engineering risk. Trade-offs, advantages and disadvantages of each option are put into perspective with a discussion of future trends, showing where this field is heading, what is driving it and what the most important unanswered questions are.

High Speed Data Converters covers high speed data converters from the perspective of a leading high speed ADC designer and architect, with a strong emphasis on high speed Nyquist A/D converters. For our purposes, the term "high speed" is defined as sampling rates that are greater than 10 MS/s. The book is intended for engineers and students who design, evaluate or use high speed data converters. A basic foundation in circuits, devices and signal processing is required. The book is meant to bridge the gap between analysis and design, theory and practice, circuits and systems. It covers basic analog circuits and digital signal processing algorithms. There is a healthy dose of theoretical analysis in this book, combined with the practical issues and intuitive perspectives. Topics covered include: * Introduction to high-speed data conversion * Performance Metrics * Data Converter Architectures * Sampling * Comparators * Amplifiers * Pipelined A/D Converters * Time-interleaved Converters * Digitally Assisted Converters * Evolution and Trends

CMOS Data Converters for Communications distinguishes itself from other data converter books by emphasizing system-related aspects of the design and frequency-domain measures. It explains in detail how to derive data converter requirements for a given communication system (baseband, passband, and multi-carrier systems). The authors also review CMOS data converter architectures and discuss their suitability for communications. The rest of the book is dedicated to high-performance CMOS data converter architecture and circuit design. Pipelined ADCs, parallel ADCs with an improved passive sampling technique, and oversampling ADCs are the focus for ADC architectures, while current-steering DAC modeling and implementation are the focus for DAC architectures. The principles of the switched-current and the switched-capacitor techniques are reviewed and their applications to crucial functional blocks such as multiplying DACs and integrators are detailed. The book outlines the design of the basic building blocks such as operational amplifiers, comparators, and reference generators with emphasis on the practical aspects. To operate analog circuits at a reduced supply voltage, special circuit techniques are needed. Low-voltage techniques are also discussed in this book. CMOS Data Converters for Communications can be used as a reference book by analog circuit designers to understand the data converter requirements for communication applications. It can also be used by telecommunication system designers to understand the difficulties of certain performance requirements on data converters. It is also an excellent resource to prepare analog students for the new challenges ahead.

This textbook is appropriate for use in graduate-level curricula in analog-to-digital conversion, as well as for practicing engineers in need of a state-of-the-art reference on data converters. It discusses various analog-to-digital conversion principles, including sampling, quantization, reference generation, nyquist architectures and sigma-delta modulation. This book presents an overview of the state of the art in this field and focuses on issues of optimizing accuracy and speed, while reducing the power level. This new, third edition emphasizes novel calibration concepts, the specific requirements of new systems, the consequences of 22-nm technology and the need for a more statistical approach to accuracy. Pedagogical enhancements to this edition include additional, new exercises, solved examples to introduce all key, new concepts and warnings, remarks and hints, from a practitioner's perspective, wherever appropriate. Considerable background information and practical tips, from designing a PCB, to lay-out aspects, to trade-offs on system level, complement the discussion of basic principles, making this book a valuable reference for the experienced engineer.

Analog-to-Digital Converters (ADCs) play an important role in most modern signal processing and wireless communication systems where extensive signal manipulation is necessary to be performed by complicated digital signal processing (DSP) circuitry. This trend also creates the possibility of fabricating all functional blocks of a system in a single chip (System On Chip - SoC), with great reductions in cost, chip area and power consumption. However, this tendency places an increasing challenge, in terms of speed, resolution, power consumption, and noise performance, in the design of the front-end ADC which is usually the bottleneck of the whole system, especially under the unavoidable low supply-voltage imposed by technology scaling, as well as the requirement of battery operated portable devices. Generalized Low-Voltage Circuit Techniques for Very High-Speed Time-Interleaved Analog-to-Digital Converters will present new techniques tailored for low-voltage and high-speed Switched-Capacitor (SC) ADC with various design-specific considerations.

This book is intended for image sensor professionals and those interested in the boundary between sensor systems and analog and mixed-signal integrated circuit design. It provides in-depth tips and techniques necessary to understand and implement these two types of complex circuit systems together for a wide variety of architectures or trade off one against another. The tutorial begins with a brief introduction to the history and definition of a digital image sensor, as well as converter characteristics, before addressing DAC and ADC architectures. Later chapters cover pipeline ADC designs, digital correction, calibration, and testing according to IEEE standards.