Serviceability failures of concrete structures involving excessive cracking or deflection are relatively common, even in structures that comply with code requirements. This is often as a result of a failure to adequately account for the time-dependent deformations of concrete in the design of the structure. The serviceability provisions embodied in

CREEP, SHRINKAGE AND DURABILITY MECHANICS OF CONCRETE AND CONCRETE STRUCTURES contains the keynote lectures, technical reports and contributed papers presented at the Eighth International Conference on Creep, Shrinkage and Durability of Concrete and Concrete Structures (CONCREEP8, Ise-shima, Japan, 30 September - 2 October 2008). The topics covered

Hat ein Werkstoff seine Elastizitatsgrenze erreicht, so verhalt er sich inelastisch. Ingenieure und Designer mussen wissen, mit welchen Eigenschaften dann zu rechnen ist. Dieser Band vermittelt Ihnen den aktuellen Wissensstand auf dem Gebiet des plastischen Verhaltens und der plastischen Zug-Spannungs-Beziehungen. Behandelt werden in erster Linie Baustoffe, vor allem Stahl, aber auch Beton und Boden. Eine ausgewogene Mischung aus qualitativer Diskussion und mathematischer Theorie! (05/00)

This book is based on Reinforced Concrete-Prestressed Concrete, Volume 2, Accounting for the Effects of Creep and Shrinkage on the Behavior of Structural Systems by Hubert Rusch and Dieter Jungwirth, which appeared in German in 1976. Even then, it was Hubert Rusch's fervent wish to have his thoughts on the deformations of concrete translated into English in order to reach a wider audience. His earlier efforts to contribute a study to the Series of Monographs of the Ameri can Institute had unfortunately not succeeded. Despite a serious illness, Hubert Rusch undertook, with his characteristic prudence and thoroughness, the preparatory work for the translation and related revision of his book. Unfortunately fate did not grant him the satisfaction of seeing his work completed. Hubert Rusch died on October 17, 1979. In writing this book, Hubert Rusch drew on his many years of devoted study of the creep problem. These investigations go back to 1934. His awareness of the plastic deformation of concrete under sustained load, which had been reported to him on the occasion of an American sojourn, led him to discover the causes of a major building collapse. At his urging, Professor A. Hummel published, in 1935, a critical survey of the test results then available on concrete creep.

The second edition of the Structural Concrete Textbook is an extensive revision that reflects advances in knowledge and technology over the past decade. It was prepared in the intermediate period from the CEP-FIP Model Code 1990 (MC90) tofib Model Code 2010 (MC2010), and as such incorporates a significant amount of information that has been already finalized for MC2010, while keeping some material from MC90 that was not yet modified considerably. The objective of the Textbook is to give detailed information on a wide range of concrete engineering from selection of appropriate structural system and also materials, through design and execution and finally behaviour in use. The revised fib Structural Concrete Textbook covers the following main topics: phases of design process, conceptual design, short and long term properties of conventional concrete (including creep, shrinkage, fatigue and temperature influences), special types of concretes (such as self compacting concrete, architectural concrete, fibre reinforced concrete, high and ultra high performance concrete), properties of reinforcing and prestressing materials, bond, tension stiffening, moment-curvature, confining effect, dowel action, aggregate interlock; structural analysis (with or without time dependent effects), definition of limit states, control of cracking and deformations, design for moment, shear or torsion, buckling, fatigue, anchorages, splices, detailing; design for durability (including service life design aspects, deterioration mechanisms, modelling of deterioration mechanisms, environmental influences, influences of design and execution on durability); fire design (including changes in material and structural properties, spalling, degree of deterioration), member design (linear members and slabs with reinforcement layout, deep beams); management, assessment, maintenance, repair (including, conservation strategies, risk management, types of interventions) as well as aspects of execution (quality assurance), formwork and curing. The updated Textbook provides the basics of material and structural behaviour and the fundamental knowledge needed for the design, assessment or retrofitting of concrete structures. It will be essential reading material for graduate students in the field of structural concrete, and also assist designers and consultants in understanding the background to the rules they apply in their practice. Furthermore, it should prove particularly valuable to users of the new editions of Eurocode 2 for concrete buildings, bridges and container structures, which are based only partly on MC90 and partly on more recent knowledge which was not included in the 1999 edition of the Textbook.

This book presents a detailed study of the flexural strengthening of reinforced and prestressed concrete members using fibre reinforced polymer composite plates. The authors also discuss plate bonding onto other engineering materials such as steel and cast iron. The book has been designed for practising civil and structural engineers seeking to understand the principles and design technology of plate bonding, and for final year undergraduates and postgraduate engineers studying the principles of highway and bridge engineering and structural engineering.

The two volumes of these Proceedings contain about 200 conference papers and 10 keynote papers presented at the First International Conference on Construction Materials and Structures, held in Johannesburg, South Africa from 24 to 26 November 2014. It includes sections on Materials and characterization; Durability of construction materials; Structural implications, performance, service life; Sustainability, waste utilization, the environment; and Building science and construction.