This work is a classic reference text for metallurgists, material scientists and crystallographers. The first edition was published in 1965. The first part of that edition was revised and re-published in 1975 and again in 1981. The present two-part set represents the eagerly awaited full revision by the author of his seminal work, now published as Parts I and II. Professor Christian was one of the founding fathers of materials science and highly respected worldwide. The new edition of his book deserves a place on the bookshelf of every materials science and engineering department. Suitable thermal and mechanical treatments will produce extensive rearrangements of the atoms in metals and alloys, and corresponding marked variations in physical and chemical properties. This book describes how such changes in the atomic configuration are effected, and discusses the associated kinetic and crystallographic features. It deals with areas such as lattice geometry, point defects, dislocations, stacking faults, grain and interphase boundaries, solid solutions, diffusion, etc. The first part covers the general theory while the second part is concerned with descriptions of specific types of transformations.

The processing-microstructure-property relationships in steels continue to present challenges to researchers because of the complexity of phase transformation reactions and the wide spectrum of microstructures and properties achievable. This major two-volume work summarises the current state of research on phase transformations in steels and its implications for the emergence of new steels with enhanced engineering properties.Volume 1 reviews fundamentals and diffusion-controlled phase transformations. After a historical overview, chapters in part one discuss fundamental principles of thermodynamics, diffusion and kinetics as well as phase boundary interfaces. Chapters in part two go on to consider ferrite formation, proeutectoid ferrite and cementite transformations, pearlite formation and massive austenite-ferrite phase transformations. Part three discusses the mechanisms of bainite transformations, including carbide-containing and carbide-free bainite. The final part of the book considers additional driving forces for transformation including nucleation and growth during austenite-to-ferrite phase transformations, dynamic strain-induced ferrite transformations (DIST) as well as the effects of magnetic fields and heating rates.With its distinguished editors and distinguished international team of contributors, the two volumes of Phase transformations in steels is a standard reference for all those researching the properties of steel and developing new steels in such areas as automotive engineering, oil and gas and energy production. - Discusses the fundamental principles of thermodynamics, diffusion and kinetics - Considers various transformations, including ferrite formation, proeutectoid ferrite and cementite transformations - Considers additional driving forces for transformation including nucleation and growth during austenite-to-ferrite phase transformations

This is the third edition of the book, much expanded to include and incorporate important developments in the subject over the last fifteen years. The book represents a comprehensive treatise on all aspects of the bainite transformation, from the choreography of atoms during the phase change to length scales that are typical of engineering applications. The alloy design that emerges from this explains the role of solute additions, and the pernicious effects of impurities such as hydrogen. The picture presented is self-consistent and therefore is able to guide the reader on the exploitation of theory to the design of some of the most exciting steels, including the world’s first bulk nanostructured metal.

Written by the leading authority in the field of solid-state phase transformations, Theory of Transformations in Steels is the first book to provide readers with a complete discussion of the theory of transformations in steel. Offers comprehensive treatment of solid-state transformations, covering the vast number in steels Serves as a single source for almost any aspect of the subject Features discussion of physical properties, thermodynamics, diffusion, and kinetics Covers ferrites, martensite, cementite, carbides, nitrides, substitutionally-alloyed precipitates, and pearlite Contains a thoroughly researched and comprehensive list of references as further and recommended reading With its broad and deep coverage of the subject, this work aims at inspiring research within the field of materials science and metallurgy.

Martensitic Transformation examines martensitic transformation based on the known crystallographical data. Topics covered range from the crystallography of martensite to the transformation temperature and rate of martensite formation. The conditions for martensite formation and stabilization of austenite are also discussed, along with the crystallographic theory of martensitic transformations. Comprised of six chapters, this book begins with an introduction to martensite and martensitic transformation, with emphasis on the basic properties of martensite in steels such as carbon steels. The next two chapters deal with the crystallography of martensite and discuss the martensitic transformation behavior of the second-order transition; lattice imperfections in martensite; and close-packed layer structures of martensites produced from ? phase in noble-metal-base alloys. Thermodynamical problems and kinetics are also analysed, together with conditions for the nucleation of martensite and problems concerning stabilization of austenite. The last chapter discusses the theory of the mechanism underlying martensitic transformation. This monograph will be of interest to metallurgists and materials scientists.

The second edition of this modern classic encompasses the latest research, which sees bainitic alloys at the forefront of a new wave of "designed" steels. Contents include: Nomenclature; Introduction; Bainitic Ferrite; Carbide Precipitation; Tempering of Bainite; Thermodynamics; Kinetics; Upper and Lower Bainite; Stress and Strain Effects; Reverse Transformation from Bainite to Austenite; Acicular Ferrite; Other Morphologies of Bainite; Mechanical Properties; Modern Bainitic Alloys;Other Aspects; The Transformation of Steel.

The properties of steels depend critically on their microstructure. By examining the mechanical properties of steels in conjunction with microstructure, the first edition gave a clear description of the development and behavior of these materials - the very foundation of their widespread use. This new edition more explicitly links this theory with applications while retaining the style and purpose of its predecessor.

The perpetual flow of understanding between phase transformation that controls grain/microstructures and heat treatment which decides the size of grains/microstructures of steels is not well articulated in the perspective of undergraduate students. In Phase Transformations and Heat Treatments of Steels, theories of phase transformation have been used to obtain a desirable phase or combination of phases by performing appropriate heat treatment operations, leading to unification of both the concepts. Further, it includes special and critical heat treatment practices, case studies, local and in-service heat treatments, curative and preventive measures of heat treatment defects for several common and high-performance applications. Features: Presents fundamentals of phase transformation in steels Analyzes basics of phase transformation due to heat treatment of steel under various environmental conditions Explains application of heat treatment for different structural components Discusses heat treatment defects and detection Emphasizes heat treatment of special steels and in-situ heat treatment practices