This report provides guidance for the design and application of shoulder and centerline rumble strips as an effective crash reduction measure, while minimizing adverse effects for motorcyclists, bicyclists, and nearby residents. Using the results of previous studies and the research conducted under this project, safety effectiveness estimates were developed for shoulder rumble strips on rural freeways and rural two-lane roads and for centerline rumble strips on rural and urban two-lane roads.

This report provides guidance for the design and application of shoulder and centerline rumble strips as an effective crash reduction measure, while minimizing adverse effects for motorcyclists, bicyclists, and nearby residents. Using the results of previous studies and the research conducted under this project, safety effectiveness estimates were developed for shoulder rumble strips on rural freeways and rural two-lane roads and for centerline rumble strips on rural and urban two-lane roads.

Following the wide and successful use of continuous shoulder rumble strips, many state departments of transportations (DOTs) installed centerline rumble strips (CLRS) on rural two-lane and undivided multilane highways in an effort to reduce cross-over-the-centerline (COCL) crashes. COCL crashes include head-on, sideswipe opposite direction, fixed object run-off-the-road left, and non-collision. The purpose of this research was to develop guidelines for using CLRS in Virginia based on a review of best practices and the analysis of Virginia COCL crash data from 2001 through 2003. The analysis procedures included data query and analyses of crash frequency, density, and rate. Areas and route locations with the highest COCL crashes and densities were identified as potential candidate sites for CLRS. As of 2003, 24 state DOTs and two Canadian provinces were using CLRS. They are generally installed on a case-by-case basis. CLRS design patterns vary greatly among states, but the most commonly used types are continuous grooves 12 to 16 inches in length, 6 to 7 inches in width, and 0.5 inch in depth spaced 12 or 24 inches apart. The optimal CLRS patterns remain unknown. Data analyses revealed that the distribution of COCL crashes in Virginia varied significantly with roadway system, road type, jurisdictional area, and road location. The statewide COCL crash densities were 0.13 and 0.71 crash per mile for secondary and primary roads, respectively. Fixed object run-off-the-road left was the predominant type of COCL crash followed by sideswipe opposite direction and head-on for undivided roads. The crash density of the primary system was 4.5 times higher than that of the secondary system. Guidelines were developed that outline the application of CLRS, design dimensions, installation and maintenance, and other issues. The authors recommend that the Virginia Department of Transportation's Traffic Engineering Division implement the guidelines as a division memorandum. Although a benefit-cost ratio for this recommendation will vary with each site, a sample estimated benefit-cost ratio was at least 7.6 per mile.

TRB's National Cooperative Highway Research Program (NCHRP) Report 672: Roundabouts: An Informational Guide - Second Edition explores the planning, design, construction, maintenance, and operation of roundabouts. The report also addresses issues that may be useful in helping to explain the trade-offs associated with roundabouts. This report updates the U.S. Federal Highway Administration's Roundabouts: An Informational Guide, based on experience gained in the United States since that guide was published in 2000.

"This report completes and updates the first edition of NCHRP Report 600: Human Factors Guidelines for Road Systems (HFG), which was published previously in three collections. The HFG contains guidelines that provide human factors principles and findings for consideration by, and is a resource document for, highway designers, traffic engineers, and other safety practitioners."--Foreword.

This book discusses the latest advances in research and development, design, operation and analysis of transportation systems and their complementary infrastructures. It reports on both theories and case studies on road and rail, aviation and maritime transportation. Further, it covers a wealth of topics, from accident analysis, vehicle intelligent control, and human-error and safety issues to next-generation transportation systems, model-based design methods, simulation and training techniques, and many more. A special emphasis is placed on smart technologies and automation in transport, and on the user-centered, ergonomic and sustainable design of transport systems. The book, which is based on the AHFE 2019 International Conference on Human Factors in Transportation, held on July 24-28, 2019, in Washington D.C., USA, mainly addresses the needs of transportation system designers, industrial designers, human–computer interaction researchers, civil and control engineers, as well as vehicle system engineers. Moreover, it represents a timely source of information for transportation policy-makers and social scientists whose work involves traffic safety, management, and sustainability issues in transport.