The combined effects of oxidising media and heat result in degradation by thermo-oxidation. The principles and cases described in this review emphasise long term degradation in service. Two additional phenomena that influence thermo-oxidation are also described: catalysis by certain metal ions, and the influence of stress. An additional indexed section containing several hundred abstracts from the Polymer Library gives useful references for further reading.

Degradation reactions grouped under the heading chemical attack include oxidation hydrolysis, halogenation and other reactions. They also include some purely physical interactions between materials and fluids, dominated by the absorption of fluid into the material or vice versa. One particular mechanism described in some detail is acid induced stress corrosion cracking, which is the most frequent cause of premature failure of GRP products, and where the principle degradation reaction is between the fluid and the glass fibres. An additional indexed section containing several hundred abstracts from the Rapra Polymer Library database gives useful references for further reading.

Rubber components are used in many demanding applications, from tyres and seals to gloves and medical devices, and failure can be catastrophic. This review of Rubber Product Failure outlines and illustrates the common causes of failure, while addressing ways of avoiding it. There has been increasing pressure to improve performance so that rubbers can be used at higher temperatures and in harsher environments. For example, the under-the-bonnet temperature has increased in some vehicles and new medical devices require longer lifetimes in potentially degrading biological fluids. The expectations of tyre performance in particular are increasing, and retreads have been in the spotlight for failures. The definition of failure depends on the application. For example, a racing car engine seal that lasts for one race may be acceptable, but in a normal car a life span of 10 years is more reasonable. If appearance is critical as in surface coatings and paints, then discolouration is failure, whilst in seals leakage is not acceptable. Each rubber product must be fit for the use specified by the consumer. Failure analysis is critical to product improvement. the cause of the problem can be much harder to find. It can range from a design fault to poor material selection, to processing problems, to manufacturing errors such as poor dimensional tolerances, to poor installation, product abuse and unexpected service conditions. The rubber technologist must become a detective, gathering evidence, understanding the material type and using deductive reasoning. Testing and analysis of failed materials and components add to the information available for failure analysis. For example, stored aged tyres appeared superficially to be alright for use, but on drum testing small cracks grew more quickly than in new tyres leading to rapid failure in service. Quality control procedures such as product inspection, testing and material quality checks can help to reach 100 percent reliability. In critical applications such as electricians' gloves for high voltage working, gloves are inspected before each use, while engine seals may be routinely replaced before the expected lifetime to avoid problems. in the literature is not high. However, several reviews have been written on specific products and references can be found at the end of this review. Around 400 abstracts from papers in the Polymer Library are included with an index. Subjects covered include tyre wear and failure, seals, engine components, rubber bonding failure, rubber failure due to chloramine in water, tank treads, gloves and condoms, medical devices and EPDM roofing membranes.

This review describes the process of life cycle analysis in some detail. It describes the different organisations involved in researching and applying these techniques and the database resources being used to generate comparative reports. The overview explains the factors to be considered, the terminology, the organisations involved in developing these techniques and the legislation which is driving the whole process forward. The ISO standards relating to environmental management are also discussed briefly in the document. Design for the environment is covered in the report. This review is accompanied by summaries of selected papers on life cycle analysis and environmental impact from the Rapra Polymer Library database.

This report presents an overview of the chemical analysis of thermosets. Materials based on thermosets present the analyst with considerable challenges due to their complexity and the wide range of polymer types and additives available. This review sets out to present an introduction to the analytical techniques and methods that are used to characterise and carry out quality control work on thermosets, investigate the failure of thermosets products and to deformulate thermoset compounds. The review is accompanied by around 400 abstracts from papers and books in the Rapra Polymer Library database, to facilitate further reading on this subject.

The review sets out to highlight the major developments in this field over the last decade. The different techniques used to prepare PLS nanocomposites are covered. The physicochemical characterisation of PLS nanocomposites and the improved materials properties that those materials can display are discussed. An additional indexed section containing several hundred abstracts from the Rapra Polymer Library database provides useful references for further reading.

Technical d104iles are high performance speciality materials. Applications are found in inflatable structures, tents, as reinforcement in composites for construction, as body armour and vehicle protection, in filters, as a base for flexible printed circuits, hose, conveyor belts and tyres. Polymer Enhancement of Technical d104iles examines the potential for these materials. The review is accompanied by around 400 abstracts from papers and books in the Rapra Polymer Library database.

Polymers have been used in agriculture and horticulture since the middle of the last century. There is a tremendous potential for using polymers in agriculture and our fields and garden would look very different if we did not use polymers in them. This review traces the history of polymer use, discusses the markets for polymers in these applications, and describes in detail the different types of polymers that can be used and their specific applications. An additional indexed section containing several hundred abstracts from the Polymer Library gives useful references for further reading.

Annotation The review focuses on the use of pharmaceutical polymer for controlled drug delivery applications. Examples of pharmaceutical polymers and the principles of controlled drug delivery are outlined and applications of polymers for controlled drug delivery are described. The field of controlled drug delivery is vast therefore this review aims to provide an overview of the applications of pharmaceutical polymers. The review is accompanied by approximately 250 abstracts taken from papers and books in the Rapra Polymer Library database, to facilitate further reading on this subject.