In the conventional classes of power amplifiers the efficiency drops at power back-off, whereas in order to maximize the spectral efficiency and data rate, wireless communication standards employ signals with high peak to average power ratio. This results in low average efficiency for power amplifiers, which in turn results in heavy cooling requirements and damage to the environment. To improve the low back-off efficiency Doherty technique has been widely investigated. But, the conventional Doherty power amplifiers are fairly narrowband, while modern transmitters are needed to support multiple standards and operate at multiple frequency bands. This thesis proposes two novel output combiners for Doherty power amplifiers with extended bandwidth. It will be shown analytically how the problem of wideband Doherty can be converted into an impedance synthesization problem. Then two networks to synthesize the desired impedance are proposed. To achieve the proper load modulation over a wide bandwidth, the first proposed combiner employs a quarter-wave short-circuited stub at the output of the peaking transistor and the second proposed combiner uses a parallel LC tank at the same node. In addition to inherent wideband characteristics, the proposed Doherty output combiners have three other important benefits. First, they present small low-frequency impedance for both the main and peaking transistors, which results in improved linearity and linearizability when the amplifier is concurrently driven with multi-band modulated signals. Second, the new combiners result in smaller group delay variation across the band compared to the conventional Doherty amplifier, which results in improved linearizability when the amplifier is driven with extra wideband modulated signals. Finally, the output capacitance of the peaking transistor can be easily absorbed into the combiners without compromising the performance of the amplifier. The thesis starts with an overview of the Doherty power amplifier principles and provides a bandwidth analysis for the conventional Doherty power amplifier. Then it continues with the new approach to extend the bandwidth of Doherty amplifiers with respect to requirements of multi-band transmission. Based on the proposed combiners, two Gallium Nitride 20 W Doherty power amplifiers have been designed and fabricated. The measurement results have been provided to validate the developed theory. The first amplifier covers 1.72 to 2.27 GHz and the second one covers 700 to 950 MHz and both maintain higher than 48 % of drain efficiency at 6 dB back-off across the band. The two amplifiers are successfully linearized when driven with carrier aggregated modulated signals.

This book introduces systematic design methods for passive and active RF circuits and techniques, including state-of-the-art digital enhancement techniques. As the very first book dedicated to multiband RF circuits and techniques, this work provides an overview of the evolution of transmitter architecture and discusses current digital predistortion techniques. Readers will find a collection of novel research ideas and new architectures in concurrent multiband power dividers, power amplifiers and related digital enhancement techniques. This book will be of great interest to academic researchers, R&D engineers, wireless transmitter and protocol designers, as well as graduate students who wish to learn the core architectures, principles and methods of multiband RF circuits and techniques.

This book focuses on broadband power amplifier design for wireless communication. Nonlinear model embedding is described as a powerful tool for designing broadband continuous Class-J and continuous class F power amplifiers. The authors also discuss various techniques for extending bandwidth of load modulation based power amplifiers, such as Doherty power amplifier and Chireix outphasing amplifiers. The book also covers recent trends on digital as well as analog techniques to enhance bandwidth and linearity in wireless transmitters. Presents latest trends in designing broadband power amplifiers; Covers latest techniques for using nonlinear model embedding in designing power amplifiers based on waveform engineering; Describes the latest techniques for extending bandwidth of load modulation based power amplifiers such as Doherty power amplifier and Chireix outphasing amplifiers; Includes coverage of hybrid analog/digital predistortion as wideband solution for wireless transmitters; Discusses recent trends on on-chip power amplifier design with GaN /GaAs MMICs for high frequency applications.

Broadband RF and Microwave Amplifiers provides extensive coverage of broadband radio frequency (RF) and microwave power amplifier design, including well-known historical and recent novel schematic configurations, theoretical approaches, circuit simulation results, and practical implementation strategies. The text begins by introducing two-port networks to illustrate the behavior of linear and nonlinear circuits, explaining the basic principles of power amplifier design, and discussing impedance matching and broadband power amplifier design using lumped and distributed parameters. The book then: Shows how dissipative or lossy gain-compensation-matching circuits can offer an important trade-off between power gain, reflection coefficient, and operating frequency bandwidth Describes the design of broadband RF and microwave amplifiers using real frequency techniques (RFTs), supplying numerous examples based on the MATLAB® programming process Examines Class-E power amplifiers, Doherty amplifiers, low-noise amplifiers, microwave gallium arsenide field-effect transistor (GaAs FET)-distributed amplifiers, and complementary metal-oxide semiconductor (CMOS) amplifiers for ultra-wideband (UWB) applications Broadband RF and Microwave Amplifiers combines theoretical analysis with practical design to create a solid foundation for innovative ideas and circuit design techniques.

This book provides a comprehensive overview of the latest research and standardization progress towards the 5th generation (5G) of mobile communications technology and beyond. It covers a wide range of topics from 5G use cases and their requirements, to spectrum, 5G end-to-end (E2E) system architecture including core network (CN), transport network (TN) and radio access network (RAN) architecture, network slicing, security and network management. It further dives into the detailed functional design and the evaluation of different 5G concepts, and provides details on planned trials and pre-commercial deployments across the globe. While the book naturally captures the latest agreements in 3rd Generation Partnership Project (3GPP) New Radio (NR) Release 15, it goes significantly beyond this by describing the likely developments towards the final 5G system that will ultimately utilize a wide range of spectrum bands, address all envisioned 5G use cases, and meet or exceed the International Mobile Telecommunications (IMT) requirements for the year 2020 and beyond (IMT-2020). 5G System Design: Architectural and Functional Considerations and Long Term Research is based on the knowledge and consensus from 158 leading researchers and standardization experts from 54 companies or institutes around the globe, representing key mobile network operators, network vendors, academic institutions and regional bodies for 5G. Different from earlier books on 5G, it does not focus on single 5G technology components, but describes the full 5G system design from E2E architecture to detailed functional design, including details on 5G performance, implementation and roll-out.

A self-contained guide to microwave electronics, covering passive and active components, linear, low-noise and power amplifiers, microwave measurements, and CAD techniques. It is the ideal text for graduate and senior undergraduate students taking courses in microwave and radio-frequency electronics, as well as professional microwave engineers.

RFIC is the premier IC Conference focused on the latest developments in RF Microwave, and Millimeter Wave Integrated Circuit Technology and Innovation

This book addresses the true innovation in engineering design that may be promoted by blending together models and methodologies from different disciplines, and, in this book, the target was exactly to follow this approach to deliver a new disruptive architecture to deliver these next-generation mobile small cell technologies. According to this design philosophy, the work within this book resides in the intersection of engineering paradigms that includes “cooperation”, “network coding”, and “smart energy-aware frontends”. These technologies will not only be considered as individual building blocks, but re-engineered according to an inter-design approach resulting in the enabler for energy efficient femtocell-like services on the move. The book aims to narrow the gap between the current networking technologies and the foreseen requirements that are targeted at the future development of the 5G mobile and wireless communications networks in terms of the higher networking capacity, the ability to support more users, the lower cost per bit, the enhanced energy efficiency, and adaptability to new services and devices (for example, smart cities, and the Internet of things (IoT)).

This book provides a detailed review of millimeter-wave power amplifiers, discussing design issues and performance limitations commonly encountered in light of the latest research. Power amplifiers, which are able to provide high levels of output power and linearity while being easily integrated with surrounding circuitry, are a crucial component in wireless microwave systems. The book is divided into three parts, the first of which introduces readers to mm-wave wireless systems and power amplifiers. In turn, the second focuses on design principles and EDA concepts, while the third discusses future trends in power amplifier research. The book provides essential information on mm-wave power amplifier theory, as well as the implementation options and technologies involved in their effective design, equipping researchers, circuit designers and practicing engineers to design, model, analyze, test and implement high-performance, spectrally clean and energy-efficient mm-wave systems.

Following on from the successful first edition (March 2012), this book gives a clear explanation of what LTE does and how it works. The content is expressed at a systems level, offering readers the opportunity to grasp the key factors that make LTE the hot topic amongst vendors and operators across the globe. The book assumes no more than a basic knowledge of mobile telecommunication systems, and the reader is not expected to have any previous knowledge of the complex mathematical operations that underpin LTE. This second edition introduces new material for the current state of the industry, such as the new features of LTE in Releases 11 and 12, notably coordinated multipoint transmission and proximity services; the main short- and long-term solutions for LTE voice calls, namely circuit switched fallback and the IP multimedia subsystem; and the evolution and current state of the LTE market. It also extends some of the material from the first edition, such as inter-operation with other technologies such as GSM, UMTS, wireless local area networks and cdma2000; additional features of LTE Advanced, notably heterogeneous networks and traffic offloading; data transport in the evolved packet core; coverage and capacity estimation for LTE; and a more rigorous treatment of modulation, demodulation and OFDMA. The author breaks down the system into logical blocks, by initially introducing the architecture of LTE, explaining the techniques used for radio transmission and reception and the overall operation of the system, and concluding with more specialized topics such as LTE voice calls and the later releases of the specifications. This methodical approach enables readers to move on to tackle the specifications and the more advanced texts with confidence.