Analysis and Design of Energy Geostructures gathers in a unified framework the theoretical and experimental competence available on energy geostructures: innovative multifunctional earth-contact structures that can provide renewable energy supply and structural support to any built environment. The book covers the broad, interdisciplinary and integrated knowledge required to address the analysis and design of energy geostructures from energy, geotechnical and structural perspectives. This knowledge includes (Part A) an introduction to the technology; (Part B) the fundamentals of heat and mass transfers as well as of the mechanics of geomaterials and structures required to address the unprecedented behavior of energy geostructures; (Part C) the experimental evidence characterizing the considered geostructures; (Part D) various analytical and numerical modeling approaches to analyze the response of energy geostructures; and (Part E) the performance-based design and detailing essentials of energy geostructures. - Proposes the theoretical and practical application essentials required to address the analysis and design of energy geostructures from energy, geotechnical and structural perspectives - Presents a substantial amount of resolved exercises on key aspects governing the behavior and performance of energy geostructures to be considered in analysis and design - Summarizes and discusses the most recent scientific and technical knowledge about energy geostructures, including energy piles, energy tunnels and energy walls

Energy geostructures are a tremendous innovation in the field of foundation engineering and are spreading rapidly throughout the world. They allow the procurement of a renewable and clean source of energy which can be used for heating and cooling buildings. This technology couples the structural role of geostructures with the energy supply, using the principle of shallow geothermal energy. This book provides a sound basis in the challenging area of energy geostructures. The objective of this book is to supply the reader with an exhaustive overview on the most up-to-date and available knowledge of these structures. It details the procedures that are currently being applied in the regions where geostructures are being implemented. The book is divided into three parts, each of which is divided into chapters, and is written by the brightest engineers and researchers in the field. After an introduction to the technology as well as to the main effects induced by temperature variation on the geostructures, Part 1 is devoted to the physical modeling of energy geostructures, including in situ investigations, centrifuge testing and small-scale experiments. The second part includes numerical simulation results of energy piles, tunnels and bridge foundations, while also considering the implementation of such structures in different climatic areas. The final part concerns practical engineering aspects, from the delivery of energy geostructures through the development of design tools for their geotechnical dimensioning. The book concludes with a real case study. Contents Part 1. Physical Modeling of Energy Piles at Different Scales 1. Soil Response under Thermomechanical Conditions Imposed by Energy Geostructures, Alice Di Donna and Lyesse Laloui. 2. Full-scale In Situ Testing of Energy Piles, Thomas Mimouni and Lyesse Laloui. 3. Observed Response of Energy Geostructures, Peter Bourne-Webb. 4. Behavior of Heat-Exchanger Piles from Physical Modeling, Anh Minh Tang, Jean-Michel Pereira, Ghazi Hassen and Neda Yavari. 5. Centrifuge Modeling of Energy Foundations, John S. McCartney. Part 2. Numerical Modeling of Energy Geostructures 6. Alternative Uses of Heat-Exchanger Geostructures, Fabrice Dupray, Thomas Mimouni and Lyesse Laloui. 7. Numerical Analysis of the Bearing Capacity of Thermoactive Piles Under Cyclic Axial Loading, Maria E. Suryatriyastuti, Hussein Mroueh , Sébastien Burlon and Julien Habert. 8. Energy Geostructures in Unsaturated Soils, John S. McCartney, Charles J.R. Coccia , Nahed Alsherif and Melissa A. Stewart. 9. Energy Geostructures in Cooling-Dominated Climates, Ghassan Anis Akrouch, Marcelo Sanchez and Jean-Louis Briaud. 10. Impact of Transient Heat Diffusion of a Thermoactive Pile on the Surrounding Soil, Maria E. Suryatriyastuti, Hussein Mroueh and Sébastien Burlon. 11. Ground-Source Bridge Deck De-icing Systems Using Energy Foundations, C. Guney Olgun and G. Allen Bowers. Part 3. Engineering Practice 12. Delivery of Energy Geostructures, Peter Bourne-Webb with contributions from Tony Amis, Jean-Baptiste Bernard, Wolf Friedemann, Nico Von Der Hude, Norbert Pralle, Veli Matti Uotinen and Bernhard Widerin. 13. Thermo-Pile: A Numerical Tool for the Design of Energy Piles, Thomas Mimouni and Lyesse Laloui. 14. A Case Study: The Dock Midfield of Zurich Airport, Daniel Pahud. About the Authors Lyesse Laloui is Chair Professor, Head of the Soil Mechanics, Geoengineering and CO2 storage Laboratory and Director of Civil Engineering at the Swiss Federal Institute of Technology (EPFL) in Lausanne, Switzerland. Alice Di Donna is a researcher at the Laboratory of Soil Mechanics at the Swiss Federal Institute of Technology (EPFL) in Lausanne, Switzerland.

This book gathers the latest advances, innovations, and applications in the field of computational geomechanics, as presented by international researchers and engineers at the 16th International Conference of the International Association for Computer Methods and Advances in Geomechanics (IACMAG 2020/21). Contributions include a wide range of topics in geomechanics such as: monitoring and remote sensing, multiphase modelling, reliability and risk analysis, surface structures, deep structures, dams and earth structures, coastal engineering, mining engineering, earthquake and dynamics, soil-atmosphere interaction, ice mechanics, landfills and waste disposal, gas and petroleum engineering, geothermal energy, offshore technology, energy geostructures, geomechanical numerical models and computational rail geotechnics.

Smart Geotechnics for Smart Societies contains the contributions presented at the 17th Asian Regional Conference on Soil Mechanics and Geotechnical Engineering (17th ARC, Astana, Kazakhstan, 14-18 August, 2023). The topics covered include: - Geomaterials for soil improvement - Tunneling and rock engineering - Slope, embankments and dams - Shallow and deep foundations - Soil dynamics and geotechnical earthquake engineering - Geoenvironmental engineering and frost geotechnics - Investigation of foundations of historical structures and monitoring - Offshore, harbor geotechnics and GeoEnergy - Megaprojects and transportation geotechnics Smart Geotechnics for Smart Societies will be of interest to academics and engineers interested or involved in geotechnical engineering.

The book collects the keynote contributions and the papers presented at the “8th Italian Conference of Researchers in Geotechnical Engineering 2023, CNRIG’23”. The conference was held on July 5–7, 2023, at the University of Palermo (Italy), and it was organized under the auspices of the National Group of Geotechnical Engineering (GNIG). The event has been organized to promote interaction among geotechnical engineering and applied sciences, with special focus on technological and digital innovations. The book covers a wide range of classical and emerging topics in geotechnics, including innovation in laboratory testing and in situ monitoring, thermo-hydro-chemo-mechanical behavior of geo-materials, computational geomechanics, analyses of instability processes in seismic conditions, probabilistic approaches, resilience of critical infrastructures and advances in risk mitigation strategies, and eco-friendly solutions for soils and rocks stabilization. This book is intended for postgraduate students, researchers, and practitioners working on geotechnical engineering and related areas.

We live in a society driven by rapid and unpredictable changes. The concept of the “fourth industrial revolution” was introduced less than ten years ago - the more aware and reality oriented “smart factories”. By this we mean novelties in production technologies, enabling IT services and greater attention to energy consumption. Today, we are discussing the fifth stage in the evolution of society, the advent of the 5.0 company. This book outlines strategic lines and suggests future directions for the development of the "super smart society" which takes responsibility and ensures sustainability by adhering to new smart technologies and skills. The book is intended for a broad audience working in the fields of material science and engineering, energy, environment, etc. It is an invaluable reference source for researchers, academicians, students, industrial institutions, government and independent institutes, individual research groups and scientists working in the field of industrial applications of smart manufacturing design.

High-Temperature Phase Change Materials for Thermal Energy Storage covers the fundamentals, thermal characteristics, measurement, design, and applications of high-temperature phase change materials (PCMs) for thermal energy storage, supported by examples and numerical modeling. The differences between low-temperature and high-temperature PCMs are examined with respect to thermophysical properties, phase change properties, and melting/solidification processes, with detailed coverage of how to alter or shorten the phase transition temperature range between melting and solidification, providing routes for the utilization of PCMs for specific high-temperature applications. The book also addresses key challenges, such as the design of PCM containers, phase transition temperature with little deviation, high latent heat capacity, thermal conductivity, viscosity, efficiency, ecocompatibility, and cost. This book is a valuable resource for researchers, advanced students, and scientists across the areas of energy storage, power generation, energy engineering, thermodynamics, materials science, renewable energy, energy management, mechanical engineering, and chemical engineering as well as engineers, research and development professionals, and other industry personnel with an interest in thermal energy storage design and materials. - Focuses on high-temperature PCMs for thermal energy storage, with real-life applications - Provides detailed information on fundamentals, thermal characteristics, measurement, and design - Addresses key challenges and includes examples, numerical studies, and modeling

Future buildings require not only energy efficiency but also proper building automation and control system functionalities in order to respond to the needs of occupants and energy grids. These development paths require a focus on occupant needs such as good indoor climate, easy operability, and monitoring. Another area to be tackled is energy flexibility, which is needed to make buildings responsive to the price signals of electricity grids with increasing amounts of fluctuating renewable energy generation installed both in central grids and at building sites. This Special Issue is dedicated to HVAC systems, load shifting, indoor climate, and energy and ventilation performance analyses in buildings. All these topics are important for improving the energy performance of new and renovated buildings within the roadmap of low energy and nearly zero energy buildings. To improve energy performance and, at the same time, occupant comfort and wellbeing, new technical solutions are required. Occupancy patterns and recognition, intelligent building management, demand response and performance of heating, cooling and ventilation systems are some common keywords in the articles of this Special Issue contributing to future highly performing buildings with reliable operation.